Exactly How to Install a Bathtub
Exactly How to Install a Bathtub
Blog Article
What are your ideas on Installing A Bathtub?
Setting up a bath tub isn't exactly brain surgery, but it does require strong plumbing, woodworking, and occasionally, tiling abilities. Replacing an old tub with a brand-new one is also a moderately hard project. If the old tub is conveniently accessible, the job can relocate quickly; if you have to open up a wall surface to remove the old tub and also position the new tub, the job is a lot harder. In either situation, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old bathtub and also set in the new one. Make certain you have actually certified yourself for the job as well as fit trying it. Rather than hiring a professional to take over a halfway-completed job, it is far better to take into consideration using one prior to you start. Chances are you may need an expert plumber to make tube links.
This post will assist you set up a new bathtub in your bathroom if you have currently acquired a brand-new bathtub and also do not need to change the arrangement of your previous supply of water pipelines.
Your devices as well as product list need to consist of the following:
Planning for the Installment
First of all, the supporting frame supplied with the bathroom needs to be fitted (if needed) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be suited its last placement.
Removing Old Taps
If you need to change old taps with new ones as a part of your setup, after that the first thing you must do is separate the water system. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The process of eliminating the existing taps can be rather troublesome as a result of the limited accessibility that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipes. When the supply pipes have actually been eliminated, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Making use of the two wood boards under its feet, place the tub in the required setting. The wood boards are useful in equally spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto four little points.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by checking the spirit level and also readjusting the feet on the tub up until the level checks out degree.
To mount taps, fit all-time low of the furthest versatile faucet connector to the appropriate supply pipe by making a compression join; after that do the very same for the other faucet.
Activate the water system and also check all joints as well as brand-new pipework for leakages and tighten them if necessary. Fill up the bathtub and additionally inspect the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the producer's instruction manual. Tiling and also securing around the bathtub ought to wait up until the tub has actually been made use of at least once as this will settle it right into its last placement.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the placing opening in the bath/basin making certain that the washing machines remain in place between the tap and also the sink. Safeguard the faucet in position with the supplier supplied backnut. When the tap is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former type should be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall in between the bath and also the tiling, causing problems with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your fixtures and also installations. They are sold in tubes and also cartridges, as well as are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can break fairly very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly readily available on the market. It is a good idea to fit the tiles making use of waterproof or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I imagined sharing that excerpt was a good idea. Enjoyed reading our blog? Please share it. Help somebody else discover it. I truly appreciate reading our article about How to Install a Bathtub Yourself.
Schedule Service Now Report this page